Ruijie Community

Title: How to configure PBR on ruijie EG？ [Print this page]

Author: Daisy Time: 2022-7-2 15:16
Title: How to configure PBR on ruijie EG？
I want VLAN 1 go through WAN 1, VLAN 2 go through WAN 2， how can I do it?

You can use the policy route to do it, for example
   vlan 1 is 192.168.1.0 vlan 2 is 192.168.2.0.
   WAN 1 is 10.100.10.1,  gateway is 10.100.10.254
   WAN 2 is 10.100.11.1，gateway is 10.100.11.254

Step 1 click route policy-base route， click add ACL

Step 2, Add two ACL 10 and 11，set ACE to permit 192.168.1.0 and 192.168.2.0

Step 3 Configure Policy route

Finished

Author: tengsern.tan@uc Time: 2023-7-20 12:48
this is for VLAN, what about specific IP address (one client/server) only?

Author: yujiamin@ruijie Time: 2023-7-20 13:23

The Wi-Fi Hero replied at 2023-7-20 12:48
this is for VLAN, what about specific IP address (one client/server) only?

Dear sir

You can configure the ACL to match the specific IP address here and apply the ACL on different PBR rules.

Best regards
Jenny

Author: tengsern.tan@uc Time: 2023-7-21 09:44

GTAC-Jenny replied at 2023-7-20 13:23
Dear sir

You can configure the ACL to match the specific IP address here and apply the ACL on di ...

do i have to enable default route for both WAN?

Author: yujiamin@ruijie Time: 2023-7-21 09:51

The Wi-Fi Hero replied at 2023-7-21 09:44
do i have to enable default route for both WAN?

Dear sir

Yes, the default route will be added by default when you set the port to WAN port to make sure the user internet access. You can type this command: show ip route to check the EG routing.

Best regards
Jenny

Author: janzsaludaga199 Time: 2023-12-27 23:06
hello how about 3 ISP
i want this vlan10 go only ISP 1
but vlan 20 go only ISP 2 and ISP 3

Author: rickywong@multi Time: 2024-1-31 18:04
Will the Extended ACL work with PBR also?

For example,

when the Destination port is UDP 443, the Route to wan1
when the Source port is UDP 53, the Route to wan2

Author: eddz1st@gmail.c Time: 2024-9-24 21:07
Hello, can you show some configuration if there is more than 2 WAN..

example :
VLAN 20 and 30 via WAN 1 , WAN 2 , WAN 3 ( Load balanced )

and
VLAN 40 via WAN 4 and WAN 5 ( load balanced )
is this possible?

Author: v-xiewenyu@ruij Time: 2024-9-24 23:00

XjawZx replied at 2024-9-24 21:07
Hello, can you show some configuration if there is more than 2 WAN..

example :

Dear Sir,
Good day.
To configure PBR on ruijie EG, you may check this configuration guide:
https://www.ruijienetworks.com/resources/preview/ruijie-reyee-rg-eg-series-gateways-web-based-configuration-guide-B16/

Best regards,
Lex

Author: ruijie@speed-wi Time: 2025-6-17 08:30
I´m having issues trying to make intervlan traffic when PBR is configured. Im my case when I configure PBR can´t connect between VLAN 2 and 3, and so on. ¿do you have advice to solve it?

Author: liuxiyang@ruiji Time: 2025-6-17 09:16

RUIJIE SPEED replied at 2025-6-17 08:30
I´m having issues trying to make intervlan traffic when PBR is configured. Im my case when I config ...

Hi sir,

Do you mean users under vlan2 cannot communication with users under vlan3,right?
After configuring PBR , if the matching rules of policy-based routing (PBR) include inter-VLAN traffic but the next-hop or interface is not set correctly, the data packet may be discarded or forwarded incorrectly.

Best regards,
Steve

Author: ruijie@speed-wi Time: 2025-6-18 06:12

GTAC-Steve replied at 2025-6-17 09:16
Hi sir,

Do you mean users under vlan2 cannot communication with users under vlan3,right?

Thank you, as you said, chose the correct IP is important to configure the correct next-hope IP. Thank you

Author: nrquimado.ocm@g Time: 2025-7-17 09:41
how about VLAN 1 can go through WAN 1 and WAN 2 but VLAN 2 can go through WAN 2 only?

Author: guominxiang@rui Time: 2025-7-17 10:16

NELSON QUIMADO replied at 2025-7-17 09:41
how about VLAN 1 can go through WAN 1 and WAN 2 but VLAN 2 can go through WAN 2 only?

Dear,

If you want VLAN 1 to be able to pass through WAN 1 and WAN 2, but VLAN 2 to be able to pass through WAN 2 only, then you only need to configure PBR for VLAN 2, and VLAN 1 only requires the configuration for load balancing.

Best regards,
Micca

Author: guominxiang@rui Time: 2025-7-17 10:16

NELSON QUIMADO replied at 2025-7-17 09:41
how about VLAN 1 can go through WAN 1 and WAN 2 but VLAN 2 can go through WAN 2 only?

Welcome to Ruijie Community (https://community.ruijie.com/)